Ferric Phosphate Hydroxide Microstructures Affect Their Magnetic Properties

Uniformly sized and shape-controlled nanoparticles are important due to their applications in catalysis, electrochemistry, ion exchange, molecular adsorption, and electronics. Several ferric phosphate hydroxide (Fe₄(OH)₃(PO₄)₃) microstructures were successfully prepared under hydrothermal conditions. Using controlled variations in the reaction conditions, such as reaction time, temperature, and amount of hexadecyltrimethylammonium bromide (CTAB), the crystals can be grown as almost perfect hyperbranched microcrystals at 180 °C (without CTAB) or relatively monodisperse particles at 220 °C (with CTAB). The large hyperbranched structure of Fe₄(OH)₃(PO₄)₃ with a size of ∼19 μm forms with the “fractal growth rule” and shows many branches. More importantly, the magnetic properties of these materials are directly correlated to their size and micro/nanostructure morphology. Interestingly, the blocking temperature (T_B) shows a dependence on size and shape, and a smaller size resulted in a lower T_B. These crystals are good examples that prove that physical and chemical properties of nano/microstructured materials are related to their structures, and the precise control of the morphology of such functional materials could allow for the control of their performance.     

Optimized adsorption and effective disposal of Congo red dye from wastewater: Hydrothermal fabrication of MgAl-LDH nanohydrotalcite-like materials

The effectiveness of Congo red (CR) adsorption from aqueous solutions onto MgAl-layered double hydroxide (MgAl-LDH) nanosorbents was examined in this study. MgAl-LDH was synthesized using the hydrothermal method, and physicochemical characterization was performed via powdered X-ray diffraction, high-resolution transmission electron microscopy, Fourier transform infrared analysis, and zeta potential measurements. For optimum adsorption of CR onto the synthesized MgAl-LDH nanosorbent, the adsorption process was employed in batch experiments. Adsorption parameters, such as the adsorbent dosage, solution pH, contact time, and initial adsorbate concentration, vary with the adsorption kinetics and isotherm mechanism. The results of the batch experiments indicated rapid adsorption of CR dye from aqueous solutions onto MgAl-LDH during the first 30 min until equilibrium was achieved at 180 min with a dye concentration of 50 mg/100 mL and MgAl-LDH adsorbent dosage of 0.05 g. The experimental adsorption data fit adequately with the monolayer coverage under the Langmuir isotherm model (R² = 0.9792), and showed the best fit with the pseudo-second-order kinetic model (R² = 0.996). The change in zeta potential confirmed the effective adsorption interaction between the positively charged MgAl-LDH and the negatively charged CR molecules with electrostatic interactions. This work is distinguished by the successful hydrothermal preparation of MgAl-LDH in the form of homogenous nanoscale particles (～100 nm). The prepared MgAl-LDH showed a high adsorption capacity toward anionic CR dye with a maximum adsorption capacity of 769.23 mg/g. This capacity is higher than those reported for other adsorbents in previous research.     

Introduction of high valent Mo6+ in Prussian blue analog derived Co-layered double hydroxide nanosheets for improved water splitting

Herein, we report a facile method for synthesizing MoCo-layered double hydroxide (LDH) nanosheets employing Prussian blue analog (PBA) as the precursor. The introduction of Mo in Co-LDH modulates the electronic structure, increases the number of active sites and electrochemical surface area to improve the hydrogen evolution, oxygen evolution, and overall water splitting activity. As a result, PBA-derived Mo_0.25Co_0.75-LDH nanosheets demonstrated 10 mA cm^?2 current density at only 220 mV and 115 mV overpotentials for OER and HER, respectively. The overall water splitting was attained at 1.52 V cell voltage for 10 mA cm^?2 current density.     

Lattice engineering route for self-assembled nanohybrids of 2D layered double hydroxide with 0D isopolyoxovanadate: chemiresistive SO2 sensor

Tuning the interior chemical composition of layered double hydroxides (LDHs) via lattice engineering route is a unique approach to enable multifunctional applications of LDHs. In this regard, the exfoliated 2D LDH nanosheets coupled with various guest species lead to the lattice-engineered LDH-based multifunctional self-assembly with precisely tuned chemical composition. This article reports the synthesis and characterization of mesoporous zinc–chromium-LDH (ZC-LDH) hybridized with isopolyoxovanadate nanohybrids (ZCiV) via lattice-engineered self-assembly between delaminated ZC-LDH nanosheets and isopolyoxovanadate (iPOV) anions. Electrostatic self-assembly between 2D ZC-LDH monolayers and 0D iPOV significantly altered structural, morphological, and surface properties of ZC-LDH. The structural and morphological study demonstrated the formation of mesoporous interconnected sheet-like architectures composed of restacked ZCiV nanosheets with expanded surface area and interlayer spacing. In addition, the ZCiV nanohybrid resistive elements were used as a room-temperature gas sensor. The selectivity of ZCiV nanohybrid was tested for various oxidizing (SO₂, Cl₂, and NO₂) gases and reducing (LPG, CO, H₂, H₂S, and NH₃) gases. The optimized ZCiV nanohybrid demonstrated highly selective SO₂ detection with the maximum SO₂ response (72%), the fast response time (20 s), low detection limit (0.1 ppm), and long-term stability at room temperature (27 ± 2 °C). Of prime importance, ZCiV nanohybrids exhibited moderately affected SO₂ sensing responses with high relative humidity conditions (80%–95%). The outstanding SO₂ sensing performance of ZCiV is attributed to the active surface gas adsorptive sites via plenty of mesopores induced by a unique lattice-engineered interconnected sheet-like microstructure and expanded interlayer spacing.     

超微Ni(OH)2纳米粒子的合成及其对Li+的超高吸附性能

在葡萄糖水溶液中合成得到平均粒径为5 nm的α-Ni(OH)2超微纳米粒子。研究结果发现,在水溶液中葡萄糖浓度能够控制α-Ni(OH)2纳米粒子粒径的大小,我们对其中的原理进行了剖析。当没有葡萄糖存在时,合成得到的Ni(OH)2晶型为β型,且颗粒粒径尺寸分布为微米级别。另外,研究发现α-Ni(OH)2超微纳米粒子室温下对中性水溶液中Li^+具有较强的吸附性能,且这种吸附性能随粒径的减小而剧烈增大;粒径为5 nm的α-Ni(OH)2粒子对Li^+的最大吸附量为214 mg·g^-1(远大于文献报道的有关吸附剂对Li^+的吸附容量),而粒径为1μm的β-Ni(OH)2在相同条件下对Li^+的最大吸附量低于30 mg·g^-1。计算分析表明,Li^+在α-Ni(OH)2纳米粒子表面吸附满足Freundlich方程,符合层层吸附模型。     

以四乙基氢氧化铵为模板并通过转晶法合成高硅铝比的SSZ⁃13沸石分子筛

使用四乙基氢氧化铵为有机模板剂,以低硅铝比(nSiO2/nAl2O3)的Y分子筛为铝源,通过转晶法制备结晶度良好的SSZ?13沸石分子筛。从凝胶配比方面考察了不同原料组成对分子筛合成的影响,并通过X射线衍射(XRD)、扫描电子显微镜(SEM)及电感耦合等离子体(ICP)表征水热反应过程中的物相、形貌、硅铝比等变化,揭示分子筛合成过程。氨选择性催化还原(NH3?SCR)反应显示该分子筛具有优异的催化活性,为其工业上的广泛应用提供了可能性。     

An Efficient Novel Electrochemical Sensor for Simultaneous Determination of Vitamin C and Aspirin Based on a PMR/Zn-Al LDH/GCE

A sensitive, low-cost, and simple electrochemical sensor based on Zn−Al layered double hydroxide (Zn−Al LDH) combined with a polymer film of methyl red (PMR) to modify a GCE has been created for the first time. Using cyclic voltammetry (CV), the electrochemical characteristics of the newly fabricated sensor were investigated. The characterised PMR/Zn−Al LDH/GCE shows high electro-catalytic activity towards the vitamin C (AA) and aspirin (ASA) oxidation. Schematic fabrication of PMR/Zn−Al LDH/GCE for the determination of AA or ASA was presented. The new sensor demonstrated superior analytical efficiency for the simultaneous identification of AA and ASA traces in well-spaced anodic peaks, even in the presence of certain intervening species. According to experimental results, the fabricated sensor represented two well-separated oxidation peaks for AA and ASA oxidation with potential difference of 799 mV (vs. Ag/AgCl). The linear dependences of the anodic peak currents of AA and ASA on their concentrations in the ranges of 0.10–53.17 μM are good. The detection limits of AA and ASA at the PMR/Zn−Al LDH/GCE were found to be 1.26 and 1.27 μM, respectively. Meanwhile, the quantification limits of AA and ASA were calculated as 4.21 and 4.25 μM, respectively. On other hand, the limit of detection (LODs) of AA and ASA oxidation were determined to be 0.47 and 0.21 μM, respectively, according to DPV method. The effect of scan rate (100 to 800 mV/s) on the anodic peak currents of AA and ASA was examined. A sensing model mechanism has been suggested and discussed in detail. Finally, the proposed sensor displayed a good reproducibility, stability and selectivity. The developed sensor was eventually used to successfully detect AA and ASA in urine samples.     

熔盐法合成电化学性能优异的富锂层状正极材料Li_(1.5)Ni_(0.25)Mn_(0.75)O_(2.5)

采用氢氧化物共沉淀和熔盐法相结合的方法制备得到了电化学性能优异的富锂锰基Li_(1.5)Ni_(0.25)Mn_(0.75)O_(2.5)正极材料。借助X射线衍射(XRD)分析、扫描电镜(SEM)、感应耦合等离子体原子发射光谱(ICP-AES)、X射线光电子能谱(XPS)、电化学阻抗谱(EIS)和恒电流充放电测试等表征手段对材料的颗粒形貌、晶体结构和电化学性能进行了系统研究。XRD结果表明该材料具有完善的α-NaFeO2层状结构(空间群为R3m)和较低的Li~+/Ni~(2+)阳离子混排。电化学性能测试表明该材料的首次不可逆容量损失较小,且倍率性能和循环稳定性能十分优异。具体而言,在2.0~4.8V,0.1C时的首次不可逆容量损失为50mAh·g~(-1)(首次库伦效率84%);在10C时的放电比容量还能达到102mAh·g~(-1);在0.5C下循环100次后,放电比容量为205mAh·g~(-1)(容量保持率90%)。     

氧化铁对铂在碱性介质中催化氧化甲醇的促进作用

Pt催化剂是电催化领域用途最为广泛的贵金属催化剂.Pt资源稀缺,价格昂贵,同时它的物理化学特性又决定了其在多种催化反应中难以被替代.在质子交换膜燃料电池的小分子醇类电氧化过程中,难免存在Pt的毒化现象,其催化性能有待进一步提升.因此,围绕着Pt催化剂纳米结构的设计、抗毒性及反应机理的探索一直是电催化研究面临的重要课题.目前,已被广泛认可的提高Pt催化性能的方法之一是引入第二种金属,通过金属间协同效应(双功能机理)、张力效应或电子效应等对Pt的催化行为进行改性.对于由双/多金属组成的纳米结构催化剂,无论是协同效应还是电子效应,催化活性的提高都需要金属间有丰富的接触界面和恰当的邻近状态.通过调变两组元的种类、原子比和接触状态等可以实现对金属-金属界面的调控,进而调变催化剂性能.除金属助剂外,金属氧化物对Pt催化剂的助催化作用也引起广泛关注.由于金属氧化物与Pt之间的密切接触作用,氧化物的形貌特点对Pt的催化性能可产生重要影响.到目前为止,有关催化剂形貌效应的研究主要集中于贵金属纳米颗粒上(Pt,Au,Pd等),但关于金属氧化物载体/助剂的形貌对贵金属催化性能影响的研究尚不多.具有明确形貌的金属氧化物载体/助剂,暴露的晶面不同,表面原子的配位状态也不同,从而造成与之密切接触的Pt的性质发生改变.因此,金属氧化物的表面性质以及Pt-金属氧化物的界面性质将对电催化性能产生重要影响,深入阐释贵金属-金属氧化物的表/界面性质以及建立有效的构效关系,对设计和制备高效电催化剂具有一定的指导意义.为了提高Pt基催化剂活性、抗CO中毒能力以及稳定性,本文采用共沉淀法和水热法分别制备了纳米棒和六边形纳米片状的Fe2O3作为Pt催化剂的助剂,考察了助剂形貌对Pt催化剂在碱性介质中催化氧化甲醇的促进作用.通过X射线衍射、扫描电子显微镜、透射电子显微镜、X射线光电子能谱以及电化学技术对催化剂进行了表征.结果显示,Fe2O3的存在能显著提高Pt催化剂在碱性介质中对甲醇氧化的电催化性能,而且以Fe2O3纳米棒为助剂制备的Pt-Fe2O3/C-R催化剂催化活性以及稳定性比Fe2O3纳米片为助剂制备的Pt-Fe2O3/C-P催化剂更高.这种促进效应可能与助剂Fe2O3的形态有关.Pt-Fe2O3/C-R催化剂中Pt的质量比活性为5.32 A/mgPt,本征活性为162.7 A/m2Pt,分别是Pt-Fe2O3/C-P催化剂的1.67和2.04倍,是商业PtRu/C样品的4.19和6.16倍.协同效应和电子效应是Pt催化性能提升的主要原因.此外,Pt-Fe2O3/C-R样品中高价态Pt的含量较高,可能也是加速甲醇氧化反应动力学的原因之一.高价态的Pt可能会增强甲醇分子在Pt表面的吸附强度,促进Pt上甲醇氧化反应初始步.这些发现不仅可对甲醇电催化氧化机理有了更深的理解,而且对设计和制备高性能甲醇氧化电催化剂也具有一定的指导意义.     

悬浮液直接进样ICP–OES法测定高纯氧化铝中的铁、钛、硅、铬

采用悬浮液直接进样电感耦合等离子体发射光谱法(ICP–OES)测定高纯氢氧化铝中铁、钛、硅、铬的含量。悬浮液用电磁搅拌器搅拌,均匀地分散在溶液中,通过仪器蠕动泵进入雾化室,均匀无阻地导入ICP光源。Fe,Ti,Si,Cr的分析谱线分别为259.940,336.112,251.611,205.552 nm;RF功率为1 300W,等离子体气流量为13.0 L/min,雾化器气体流量为0.60 L/min,辅助气流量为1.00 L/min。Fe,Ti,Si,Cr的质量浓度分别在0.0~30.0,0.0~15.0,0.0~90.0,0.0~15.0μg/m L范围内与信号强度呈良好的线性,线性相关系数均大于0.999,方法的检出限为0.027 6~0.993 9μg/m L,测量结果的相对标准偏差为0.65%~6.84%(n=11),回收率为95.0%~104.8%。该法抗干扰能力强、线性范围宽,适用于高纯氢氧化铝中铁、钛、硅、铬含量的分析。